Derale-performance 14" Tornado Electric Fan & 180 Bedienungsanleitung PDF herunterladen

PRE INSTALLATION

PULLER APPLICATION

PUSHER APPLICATION

Note:

1. Electric Fan is setup from the factory for Puller applications and requires no

modification.

2. Check product label on Electric Fan shroud. The arrow on the label shows

airflow direction through the fan.

1. Remove the nut/clip that holds fan blade to motor shaft.

2. Remove fan blade from motor shaft. This is an interference fit and

requires some effort. Be careful not to damage fan blade.

3. Flip blade over and align groove in fan blade with roll pin on motor shaft.

4. Reinstall nut/clip on motor shaft.

INSTALLATION INSTRUCTIONS

ELECTRIC FAN

PART # 16010 & 16014

16010-16014-InstructionSheet Rev.2-08-2011

Dyno-Cool by Derale, Los Angeles, CA 800.421.6288 www.derale.com

Please read these instructions completely before beginning installation

PARTS LIST

QTY. DESCRIPTION

1 Electric Fan

4 Mounting Rods

4 Mounting Clips

5 1x1 Foam Pads

1 Thermostat Switch

1 Relay Wire Harness

1 7 Ft. 14 Ga. Wire

1 3/8” NPT Thread-in Probe

1 Push-in Probe

QTY. DESCRIPTION

1 Retaining Probe Clip

1 Blue 5/16” Ring Terminal

2 Blue #10 Ring Terminal

1 Blue Butt Connectors

2 Blue Wire Tap Connectors

4 4” Wire Ties

2 #10 Sheet Metal Screw

2 Blue Female Connectors

TOOLS NEEDED

12V Test Light

Wire Stripper

Crimping Tool

3/4” Wrench

Teflon Tape

Standard Screw Driver or

a 5/16” Nut Driver

Drill

5/32” Drill Bit

Dyke Pliers

IMPORTANT

This fan assembly is designed

for both PULLER and

PUSHER APPLICATIONS.

(See Diagram #1)

Puller Fan

Pusher Fan

Air Flow

Engine Radiator

Diagram #1

(Continues on Page 2)

ELECTRIC FAN MOUNTING

Note:

Caution:

This Electric Fan Assembly requires 4 mounting positions. (See Diagram #2)

1. Position the electric fan against the radiator in the desired location.

2. Take the Plastic Rods provided and install through the mounting holes on the shroud pushing them slowly into and through

the radiator core.

Do not use excessive force when pushing Plastic Rods through radiator core. Excessive force could cause

Damage to the radiator fins and/or core. Plastic Rods

should not be inserted thru both the radiator and the

condenser cores.

3. Take the 1 x 1 Foam pads provided and install them

onto the Plastic Rods now protruding through the

radiator core.

4. Take the Plastic Clips provided, making sure they are in

the correct direction (Derale writing out) install onto the

Plastic Rods and cinch them until the 1 x 1 Foam Pads

are compressed.

5. Cut off the excess Plastic Rod.

Diagram #2

Mounting Clips

1 x 1

Foam

Pads

Mounting

Rods

1 2 3

Inhaltsverzeichnis

Seite 1 - PART # 16010 & 16014

PRE INSTALLATIONPULLER APPLICATIONPUSHER APPLICATIONNote:1. Electric Fan is setup from the factory for Puller applications and requires nomodification

Seite 2 - Diagram #6

Dyno-Cool by Derale, Los Angeles, CA 800.421.6288 www.derale.comTHERMOSTAT PROBE INSTALLATIONOption 1This kit includes two thermostat probe options

Seite 3 - Diagram #8

Warning: Installation of accessories should only be undertaken by those with mechanical knowledge and are familiar with working onvehicles. Always use

Kommentare zu diesen Handbüchern

Keine Kommentare

Derale-performance 14" Tornado Electric Fan & 180 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Fans Derale-performance 14" Tornado Electric Fan & 180 herunter. Derale Performance 14" Tornado Electric Fan & 180 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern