Derale-performance High Output Dual Rad Fan Assembly Bedienungsanleitung PDF herunterladen

16028-16034-InstructionSheet

INSTALLATION INSTRUCTIONS

HIGH OUTPUT DUAL RAD FAN ASSEMBLY

PART # 16028 & 16034

KIT CONTENTS

QTY. DESCRIPTION

1 Left Shroud Assembly

1 Right Shroud Assembly

4 Shroud Assembly Screws

1 180° Thermostat Switch

1 3/8” Radiator Probe

1 Push-in Radiator Probe

1 1 x 1 Foam Pad

1 Retaining Clip

1 190° Thermostat Switch

1 3/8” x 1/8” Adapter Bushing

8 Mounting Rods

8 Mounting Clips

QTY. DESCRIPTION

8 1x1 Foam Pads

2 Relay Wire Harness

1 Red Butt Connector

2 Blue #10 Ring Terminals

2 Blue 5/16” Ring Terminals

3 Blue Butt Connectors

2 Blue Female Connectors

4 Blue Wire Tap connectors

7ft. 14 Gauge Wire

6 4” Wire Ties

4 #10 Sheet Metal Screws

Derale Performance, Los Angeles, CA 800.421.6288 www.derale.com

Diagram #1

Engine

Puller Fan

Air Flow

Radiator

Please read these instructions completely before beginning installation

IMPORTANT

This fan assembly is designed for PULLER APPLICATIONS

Engine side of radiator. (See Diagram #1)

ONLY

TOOLS NEEDED

5/8” Open End Wrench

11/16” Open End Wrench

3/4” Open End Wrench

Standard Screw Driver or

5/16” Nut Driver

Drill

5/32” Drill Bit

12V Test Light

Wire Stripper

Crimping Tool

Teflon Tape

MOUNTING

1. Position the electric fan against the radiator in the desired

location.

2. Take the Plastic Rods provided and install through the eight

mounting holes on the shroud pushing them slowly into and

through the radiator core. (See Diagram #3)

Do not use excessive force when pushing Plastic

Rods through radiator core. Excessive force could cause

damage to the radiator fins and/or core. Plastic Rods should

not be inserted thru both the radiator and the condenser cores.

3. Takethe1x1Foam pads provided and install them onto

the Plastic Rods now protruding through the radiator core.

(See Diagram #3)

4. Take the Plastic Clips provided, making sure they are in the

correct direction (Derale writing out) install onto the Plastic

Rods and cinch them until the1x1Foam Pads are

compressed. (See Diagram #3)

5. Cut off the excess Plastic Rod.

Caution:

Diagram #3

PRE-INSTALLATION

1. Identify the Right and Left Shroud Assembly

and Fan Shroud Mounting Screws

2. Using a table or flat surface, lay both the Right

& Left Shroud Assemblies on the flat surface

with the fan motors both facing up.

(See Diagram #2)

3. Slide both shrouds together lining up the

mounting holes. (See Diagram #2)

4. Carefully install the 4 Fan Shroud Assembly

Screws into each of the mounting holes and

tighten.

Do not over tighten!Note:

Mounting

Rods

Mounting

Clips

Foam

Pads

Electric Fan

Assembly

Diagram #2

Right Shroud Assembly

Left Shroud Assembly

(Page 1)

1 2 3 4

Inhaltsverzeichnis

Seite 1 - PART # 16028 & 16034

16028-16034-InstructionSheetINSTALLATION INSTRUCTIONSHIGH OUTPUT DUAL RAD FAN ASSEMBLYPART # 16028 & 16034KIT CONTENTSQTY. DESCRIPTION1 Left Shrou

Seite 2 - Diagram #4

Derale Performance, Los Angeles, CA 800.421.6288 www.derale.comTHERMOSTAT INSTALLATIONOption 1FAN #1 - 180° Thermostat SwitchOption 1 - Push-in Radiat

Seite 3 - Diagram #8

Derale Performance, Los Angeles, CA 800.421.6288 www.derale.comBlueFan Positive (+)30Amp FuseIgnitionSwitchBlackChassis Ground (-)Red30 868587Green12

Seite 4 - (Switch Not Included)

Derale Performance, Los Angeles, CA 800.421.6288 www.derale.comWarning: Installation of accessories should only be undertaken by those with mechanical

Kommentare zu diesen Handbüchern

Keine Kommentare

Derale-performance High Output Dual Rad Fan Assembly Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Fans Derale-performance High Output Dual Rad Fan Assembly herunter. Derale Performance High Output Dual Rad Fan Assembly User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Fans Derale-performance High Output Dual Rad Fan Assembly