Derale-performance 9" Tornado Electric Puller Fan, Standard Moun Bedienungsanleitung PDF herunterladen

KIT CONTENTS

QTY. DESCRIPTION

1 Electric Fan Assembly

4 Mounting Rod

4 Mounting Clip

4 Mounting Feet

4 1x1 Foam Pad

Please read these instructions completely before beginning installation

TOOLS NEEDED

Standard Screw Driver

12V Test Light

Wire Stripper

Crimping Tool

Dyke Pliers

PRE-INSTALLATION

Important:

This fan is factory setup for PULLER applications

Changing airflow direction

Note:

Important:

Tornado Electric Fans come from the factory with a product label

installed on one end of the fan shroud. Before installation check the product

label to confirm airflow direction and positive electric fan lead color.

Airflow direction will be shown with an arrow.

To change the airflow direction from the factory setting:

1. Remove the Nut or Clip that holds the electric fan blade onto the motor

shaft.

2. Carefully remove the fan blade from the motor shaft.

This is an interference fit and requires some effort.

3. Flip the fan blade upside down and reinstall onto the motor shaft. Make

sure the roll pin on the motor shaft is aligned with the slot on the fan blade.

4. Reinstall nut or clip on motor shaft.

For Puller applications use the referenced wire colors stated on the

Product Label. For Pusher applications the two wires MUST be reversed to

change airflow direction.

Diagram #1

Puller Fan

Pusher Fan

Air Flow

Engine Radiator

16617-16618-16619-16622-InstructionSheet

INSTALLATION INSTRUCTIONS

TORNADO ELECTRIC FAN KIT

PART # 16617, 16618, 16619, 16622

IMPORTANT

This fan assembly is designed for both PUSHER and

PULLER applications.

To change airflow direction from the factory setting,

you MUST follow the directions below or performance

will be compromised. (See Diagram #1)

(Continues on Page 2)

Derale Performance, Los Angeles, CA 800.421.6288 www.derale.com

ELECTRIC FAN MOUNTING

Note: This Electric Fan Assembly requires 4 mounting positions. Four Mounting Rods will be installed with the 4 supplied

Mounting Feet. (See Diagram #2)

1. Identify the 4 Mounting Feet supplied and install onto the Electric Fan Assembly by sliding them into the slots on the Electric

Fan Assembly. See Diagram #2

2. Position the electric fan against the radiator in the desired location.

3. Take the Plastic Rods provided and install

through the mounting holes on the shroud

pushing them slowly into and through the

radiator core.

Do not use excessive force when

pushing Plastic Rods through radiator core.

Excessive force could cause damage to the

radiator fins and/or core. Plastic Rods should

not be inserted thru both the radiator and the

condenser cores.

4. Take the 1 x 1 Foam pads provided and install

them onto the Plastic Rods now protruding

through the radiator core.

5. Take the Plastic Clips provided, making sure

they are in the correct direction (Derale writing

out) install onto the Plastic Rods and cinch them

until the 1 x 1 Foam Pads are compressed.

6. Cut off the excess Plastic Rod.

Caution:

Diagram #2

Mounting

Clips

1 x 1

Foam

Pads

Mounting

Feet

Mounting

Rods

1 2

Inhaltsverzeichnis

Seite 1 - TORNADO ELECTRIC FAN KIT

KIT CONTENTSQTY. DESCRIPTION1 Electric Fan Assembly4 Mounting Rod4 Mounting Clip4 Mounting Feet4 1x1 Foam PadPlease read these instructions completely

Seite 2 - TYPICAL MANUAL SWITCH WIRING

Warning: Installation of accessories should only be undertaken by those with mechanical knowledge and are familiar with working onvehicles. Always use

Kommentare zu diesen Handbüchern

Keine Kommentare

Derale-performance 9" Tornado Electric Puller Fan, Standard Moun Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Fans Derale-performance 9" Tornado Electric Puller Fan, Standard Moun herunter. Derale Performance 9" Tornado Electric Puller Fan, Standard Mounting Kit User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Fans Derale-performance 9" Tornado Electric Puller Fan, Standard Moun