Derale-performance 10" Tornado Electric Puller Fan, Premium Moun Bedienungsanleitung PDF herunterladen

KIT CONTENTS

QTY. DESCRIPTION

1 Electric Fan Assembly

4 Mounting Rod

4 Mounting Clip

4 1x1 Foam Pad

1 Manual Switch

7ft 14 Gauge Wire

1 20 Amp Fuse Holder

QTY. DESCRIPTION

3 Blue Female Connector

2 #10 Blue Ring Terminal

3 Blue Butt Connector

4 #10 x 1/2” Sheet Metal Screws

4 4” Zip Ties

Blue Wire Tap Connector

Please read these instructions completely before beginning installation

TOOLS NEEDED

Standard Screw Driver

Drill

5/32” Drill Bit

12V Test Light

Wire Stripper

Crimping Tool

Dyke Pliers

PRE-INSTALLATION

Important:

This fan is factory setup for PULLER applications

Changing airflow direction

Note:

Tornado Electric Fans come from the factory with a product label

installed on one end of the fan shroud. Before installation check the product

label to confirm airflow direction and positive electric fan lead color.

Airflow direction will be shown with an arrow.

To change the airflow direction from the factory setting:

1. Remove the Nut or Clip that holds the electric fan blade onto the motor

shaft.

2. Carefully remove the fan blade from the motor shaft.

This is an interference fit and requires some effort.

3. Flip the fan blade upside down and reinstall onto the motor shaft. Make

sure the roll pin on the motor shaft is aligned with the slot on the fan blade.

4. Reinstall nut or clip on motor shaft.

Important: For Puller applications use the referenced wire colors stated on the

Product Label. For Pusher applications the two wires MUST be reversed to

change airflow direction.

Diagram #1

Puller Fan

Pusher Fan

Air Flow

Engine Radiator

16510-16514-InstructionSheet.cdr

INSTALLATION INSTRUCTIONS

TORNADO ELECTRIC FAN KIT

PART # 16510 & 16514

IMPORTANT

This fan assembly is designed for

both PUSHER and PULLER

applications.

To change airflow direction from

the factory setting, you MUST

follow the directions below or

performance will be compromised.

(See Diagram #1)

(Continues on Page 2)

Derale Performance, Los Angeles, CA 800.421.6288 www.derale.com

ELECTRIC FAN MOUNTING

Note: This Electric Fan Assembly requires 4 mounting positions. (See Diagram #2)

1. Position the electric fan against the radiator in the desired location.

2. Take the Plastic Rods provided and install through the mounting holes on the shroud pushing them slowly into and through

the radiator core.

Caution: Do not use excessive force when pushing

Plastic Rods through radiator core. Excessive force

could cause damage to the radiator fins and/or core.

Plastic Rods should not be inserted thru both the

radiator and the condenser cores.

3. Take the 1 x 1 Foam pads provided and install them

onto the Plastic Rods now protruding through the

radiator core.

4. Take the Plastic Clips provided, making sure they are in

the correct direction (Derale writing out) install onto the

Plastic Rods and cinch them until the 1 x 1 Foam Pads

are compressed.

5. Cut off the excess Plastic Rod.

Diagram #2

Mounting Clips

1 x 1

Foam

Pads

Mounting

Rods

1 2

Inhaltsverzeichnis

Seite 1 - PART # 16510 & 16514

KIT CONTENTSQTY. DESCRIPTION1 Electric Fan Assembly4 Mounting Rod4 Mounting Clip4 1x1 Foam Pad1 Manual Switch7ft 14 Gauge Wire1 20 Amp Fuse HolderQTY.

Seite 2 - Diagram #4

MANUAL SWITCH MOUNTING(See Diagram #3)1. Find a location in the vehicles passenger compartment.2. Using the Manual Switch as a template, mark and dril

Kommentare zu diesen Handbüchern

Keine Kommentare

Derale-performance 10" Tornado Electric Puller Fan, Premium Moun Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Fans Derale-performance 10" Tornado Electric Puller Fan, Premium Moun herunter. Derale Performance 10" Tornado Electric Puller Fan, Premium Mounting Kit User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Fans Derale-performance 10" Tornado Electric Puller Fan, Premium Moun